GREY HAWK 6X20

GREY HAWK

6X20

1334/9117/26019

Nuevo

1655

Equipment As Follows: Metso 6x20 Three Deck Horizontal Vibrating Screen – Side Tensioned Installation Angle 0º Throw/Speed 0.625” @ 800 RPM Motor Size 50HP Triple shaft screen considered at 0 degree for operation as standard Coil springs and dampers 5/16” thick side plates with huck bolt construction Side tension decks with seal strips for 4’ screen panels Heavy duty tube steel decks with herringbone cross bracing Vibrating mechanism (160mm bearings) with oil lubrication Carriage bolts used to retain clamp bars – standard is 4’ long bars AR lined feedbox and AR line discharge lip Right hand variable speed drive standard with motor mount and belt guard and tensioning device Hand access on triple deck screens, spray bar knockouts, bottom deck feed end curtain Paint – Metso Grey Screen Configuration: Bottom Deck - Side tensioned Hand of drive – Right Screen media – Not included Metso TSE Series Screens The TSE Series screens are a horizontal screen that utilize elliptical motion vibration for superior accuracy and efficiency in compact installations. They are built for stationary and portable applications in both tertiary and primary screening and can be equipped for wet or dry screening. Improved Performance with High-Power Elliptical Vibration The elliptical motion of the screens, along with high acceleration, allows for more power than in traditional screens. This feature delivers higher throughput and screening efficiency. TSE Series screens have a 1:3 elliptical ratio. This very aggressive 1:3 ratio causes vibration of the layer of materials in two directions. It also generates faster stratification of the layer so that fines pass through the screening mesh quickly and efficiently. These characteristics contribute to the TSE Series screens superiority in processing very sticky or clay materials and materials with high content of flaky particles. Designed For the Toughest Applications The body of TSE Series screens is extremely strong, supporting the stresses required by the “high power” mechanism. This robustness is provided by frames made from heavy tube cross members with stiffeners positioned in critical areas. The side plates are huck bolted without any welding. The standard drive arrangement for the TSE Series screens is a V-belt drive. The screens are equipped with a spring-tension motor base to maintain constant belt tension, thereby reducing maintenance and extending the life span of the drive components. The mechanical parts located inside the screens are fully protected by a rubber-lined steel guard with ports to allow any dust or debris that enters the counterweight area to fall free from any moving parts. The triple shaft mechanism is comprised of 6 individual bearing and bearing housings assemblies with bolt on weights that are complemented with plug weights. The six individual assemblies are synchronized with gears which create the stroke direction as well as the elliptical motion. The bearing assemblies are locked together to ensure matching stroke from side to side. Modular Machine Design Enables Flexibility The ability to make mechanical adjustments allows you to adjust all screening parameters in order to adapt them to all types of applications. Depending on the application, the vibration amplitude can be adjusted by adding or removing unbalanced weights bolted to the counterweights. If necessary, the synchronized gears can be set in various positions, changing the vibration angle. For standard vibration, the angle is set at 45° to correspond to the normal feed speed of materials, but it is possible to adjust it to between 30° and 60°. EIW-36” FINE MATERIAL DOUBLE SCREW WASHER Fabricated steel washer tub and feed box Adjustable weirs for out of level conditions Rising current manifold Close-clearance curved plate runs entire length of shaft Outboard grease bearings Washer shaft includes flight sections welded to a flanged extra thick one-piece tube Hard white iron abrasion resistant wear shoes Dodge gear reducers, v-belt drives and v-belt drive guards Self-aligning, anti-friction roller bearings at discharge end Maximum material size: 3/8” 100% screw speed maximum capacity: 200TPH (2) 15HP motors/230-460 volt/3PH/60Hz Overflow flume Discharge chute GREYHAWK PORTABLE WASH PLANT CHASSIS MAIN CHASSIS Heavy duty mainbeam Triple-axle spring suspension (12) 11R22.5 tires on hub piloted Air controlled brakes on all axles LED side marker and tail lights Walkway around the entire screen Walkways include handrail, center rail, toe board and hinged self-closing gates Access ladders on both sides Fifth wheel hitch Air controlled brakes Travel Lights Mud flaps Hydraulically operated safety tie off supports SCREEN SUPPORT FRAME Under-screen flume made from ¼” plate Liners not included Slurry feed box w/hydraulic fold for travel Liners not included Water manifold with distribution lines to Slurry feed box (liners not included) Screen spray bars FMSW rising current DISCHARGE CHUTES Chute hydraulically rolls away from screen for maintenance Top deck overs Made from ¼” plate Discharges at the end of the structure Four blending gates allow for blending Middle deck overs Made from ¼” plate Four blending gates allow for blending Bottom deck overs Made from ¼” plate Four blending gates allow for blending Liners not included CROSS CONVEYORS-30” (QTY-2) Channel frame design Superior 5” CEMA C channel mount picking idlers Superior 5” CEMA C return idler Argonics scraper 3 ply, 3/16” top cover conveyor belting Full length rubber skirting Head Pulley Superior 10” drum pulley SCM pillow block bearings Size #2 shaft mount reducer WEG 7.5HP motor Tail Pulley Superior 10” wing pulley SCM bearings Takeups HYDRAULICS Gas powered hydraulic power unit with electric start and recoil backup (4) Hydraulic leveling cylinders Four bank valve body for independent control of each jackleg Single bank valve for slurry box positioning